開平機械是板材加工行業常用的設備。鈑金加工中使用的功率非常大。可以看出，整平機的動力系統技能要求與組成相比非常高，所以讓我們來解釋一下整平機動力系統的組成部分：

調平電動系統一般由調平動力基座，減速器，聯軸器，驅動齒輪組等組成。主電機是大功率直流電機，帶有進口數字直流控制器，可調節調平速度。一個大范圍。起動電流小于額外電流，并且起動轉矩大于額外轉矩。它特別適用于連續高負載條件，負責為主機提供調平功率。

整平機的主要部分采用四組滾子結構，包括焊接框架，所有龍門架，15個調平滾子軸，上下滾子軸座，橫梁，滾子，滾子座和蝸輪。輥增加了擠壓裝置的組成等。通過蝸輪傳動結構選擇兩個減速電機用于上輥，并且輥軸座是兩側的彎曲軌道結構。用戶可以根據需要通過調節上下調平輥的入口和出口間隙來調節調平精度。通過百分表顯示上輥的調節量。

以上我們詳細了解了整平機的動力系統。要了解有關開平機的更多信息，您可以找到我們開平機廠家。

當調平機的電動機開始減速時，電動機處于再生制動狀態。存儲在驅動系統中的停滯能量變為電能并且經由變頻器中的逆變器反饋到DC側。此時，逆變器處于整流狀態，中心電路的濾波電容器的電壓通過該部件的能量得到改善，并產生泵產生電壓。當電壓值高于約690V的上限時，制動單元電路接通，電流與濾波電容并聯流過制動電阻，從而將電能轉換為熱能，泵電壓減少了。下限設定為約680V時斷開。連續泵送泵送電壓，并重復打開和阻止制動單元，以完成系統的動態制動。在這個過程中，IPC-DR型制動單元和匹配的制動電阻很難工作：它接收有源電壓拖尾方法，響應時間低于1ms，動作電壓為DC 690V，誤差為2V，這是非常令人興奮的。

平整機維護和故障排除

1.電氣設備維護

電氣設備應在正常電壓下運行。如果電壓不斷變化，電氣元件的壽命將大大縮短，故障率將急劇增加。電氣元件應保證在干燥的環境中工作，如潮濕和雨淋，干燥后應繼續工作，暴露的線路應經常檢查其絕緣，以免發生漏電事故。

2.機器維護

機器的外露部件，更容易生銹的部件，應定期上油或上油。潤滑脂口應每15天填充一次：齒輪，鏈輪等旋轉部件應每天注滿潤滑油。

故障排除1.皮帶輸送裝置滑動，不能驅動材料;這可能是因為壓力彈簧的壓力不夠。檢查調節壓力彈簧以增加壓力。

2.飼料開始太早或太晚;這不適用于時間計的時間段，應調整誘導時間之間的間隔。

3.上下輥不旋轉;這有幾個原因，例如：鏈條關閉;電機啟動按鈕或接觸器故障;電機線關閉;電機燒壞或減速器有故障，所以我們必須檢查線路并進行重新調整。

4.無法檢測到矯直機;這可能是由傳感器線路脫落或鐘表電氣故障或電子控制元件故障引起的。處理的原因還在于檢查線路或更換組件。

5.材料左右，喂料不穩定。主要原因是進給輥和校正流輪不平行或材料太厚或太厚。解決方案是將其調整為平行或在早期階段排列材料。 。